Schneider Electric Altivar 32 Manuel d'installation télécharger pdf (Page 77)

Configuration Mode (ConF)

S1A28692 03/2010 77

Parameters described in this page can be accessed by:

Code Name / Description Adjustment range Factory setting

FULL [FULL] (continued)

SEt- [SETTINGS]

Inr [Ramp increment]

0.1

This parameter is valid for [Acceleration] (ACC), [Deceleration] (dEC), [Acceleration 2] (AC2) and

[Deceleration 2] (dE2). See [Ramp increment] (Inr) page 155

0.01

0.1

[0,01]: Ramp up to 99.99 seconds

[0,1]: Ramp up to 999.9 seconds

[1]: Ramp up to 6,000 seconds

ACC [Acceleration]

0.00 to 6,000 s (1) 3.0 s

Time to accelerate from 0 to the [Rated motor freq.] (FrS) page 74. To have repeatability in ramps, the value of this parameter

must be set according to the possibility of the application. See [Acceleration] (ACC) page 155

dEC [Deceleration]

0.00 to 6,000 s (1) 3.0 s

Time to decelerate from the [Rated motor freq.] (FrS) page 74 to 0. To have repeatability in ramps, the value of this parameter

must be set according to the possibility of the application. See [Deceleration] (dEC) page 155

AC2 [Acceleration 2]

0.00 to 6,000 s (1) 5 s

Time to accelerate from 0 to the [Rated motor freq.] (FrS) page 74. To have repeatability in ramps, the value of this parameter

must be set according to the possibility of the application. See [Acceleration 2] (AC2) page 156

dE2 [Deceleration 2]

0.00 to 6,000 s (1) 5 s

Time to decelerate from the [Rated motor freq.] (FrS) page 74 to 0. To have repeatability in ramps, the value of this parameter

must be set according to the possibility of the application. See [Deceleration 2] (dE2) page 156

tA1 [Begin Acc round]

0 to 100% 10%

Rounding of start of acceleration ramp as a % of the [Acceleration] (ACC) or [Acceleration 2] (AC2) ramp time. Visible if

[Ramp type] (rPt) is set to [Customized] (CUS). See [Begin Acc round] (tA1) page 155

tA2 [End Acc round]

0 to 100% 10%

Rounding of end of acceleration ramp as a % of the [Acceleration] (ACC) or [Acceleration 2] (AC2) ramp time.

Can be set between 0 and 100% - [Begin Acc round] (tA1).

Visible if [Ramp type] (rPt) is set to [Customized] (CUS). See [End Acc round] (tA2) page 156

tA3 [Begin Dec round]

0 to 100% 10%

Rounding of start of deceleration ramp as a % of the [Deceleration] (dEC) or [Deceleration 2] (dE2) ramp time. Visible if

[Ramp type] (rPt) is set to [Customized] (CUS). See [Begin Dec round] (tA3) page 156

tA4 [End Dec round]

0 to 100% 10%

Rounding of end of deceleration ramp as a % of the [Deceleration] (dEC) or [Deceleration 2] (dE2) ramp time.

Can be set between 0 and 100% - [Begin Dec round] (tA3).

Visible if [Ramp type] (rPt) is set to [Customized] (CUS). See [End Dec round] (tA4) page 156

LSP [Low speed]

0 to 599 Hz 0 Hz

Motor frequency at minimum reference, can be set between 0 and [High speed] (HSP) page 75. See [Low speed] (LSP)

page 75

HSP [High speed]

0 to 599 Hz 50 Hz

Motor frequency at maximum reference, can be set between [Low speed] (LSP) and [Max frequency] (tFr). The factory

setting changes to 60 Hz if [Standard mot. freq] (bFr) is set to [60Hz NEMA] (60). See [High speed] (HSP) page 75

DRI- > CONF > FULL > SET-

Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

1 2 ... 72 73 74 75 76 77 78 79 80 81 82 ... 318 319

Commentaires sur ces manuels

Pas de commentaire

Schneider Electric Altivar 32 Manuel d'installation Page 77

Commentaires sur ces manuels

Produits connexes et manuels pour Tournevis électriques Schneider Electric Altivar 32