Schneider Electric Altivar 32 Manuel d'installation télécharger pdf (Page 142)

Configuration Mode (ConF)

142 S1A28692 03/2010

Parameters described in this page can be accessed by:

As the graphic display terminal may be selected as the command and/or reference channel, its action modes

can be configured.

The parameters on this page can only be accessed on the graphic display terminal, and not on the integrated

display terminal.

Comments:

• The display terminal command/reference is only active if the command and/or reference channels from the

terminal are active with the exception of [T/K] (Ft) (command via the display terminal), which takes

priority over these channels. Press [T/K] (Ft) (command via the display terminal) again to revert control

to the selected channel.

• Command and reference via the display terminal are impossible if the latter is connected to more than one

drive.

• The JOG, preset speed and +/- speed functions can only be accessed if [Profile] (CHCF) is set to

[Not separ.] (SIM).

• The preset PID reference functions can only be accessed if [Profile] (CHCF) is set to

[Not separ.] (SIM) or [Separate] (SEP).

• The [T/K] (Ft) (command via the display terminal) can be accessed regardless of the [Profile] (CHCF).

Code Name / Description Adjustment range Factory setting

Fn1 [F1 key assignment]

[No] (nO)

FJOG

FPS1

FPS2

FPr1

FPr2

FuSP

FdSP

[No] (nO): Not assigned

[Jog] (FJOG): JOG operation

[Preset spd2] (FPS1): Press the key to run the drive at the 2nd preset speed [Preset speed 2] (SP2) page 84

. Press STOP

to stop the drive.

[Preset spd3] (FPS2): Press the key to run the drive at the 3rd preset speed [Preset speed 3] (SP3) page 84

. Press STOP

to stop the drive.

[PID ref. 2] (FPr1): Sets a PID reference equal to the 2nd preset PID reference [Preset ref. PID 2] (rP2) page 86

, without

sending a run command. Only operates if [Ref.1 channel] (Fr1) is set to [HMI] (LCC). Does not operate with the [T/K] (Ft)

function.

[PID ref. 3] (FPr2): Sets a PID reference equal to the 3rd preset PID reference [Preset ref. PID 3] (rP3) page 87

, without

sending a run command. Only operates if [Ref.1 channel] (Fr1) is set to [HMI] (LCC). Does not operate with the [T/K] (Ft)

function.

[+speed] (FUSP): Faster, only operates if [Ref.2 channel] (Fr2) is set to [HMI] (LCC). Press the key to run the drive and

increase the speed. Press STOP to stop the drive.

[- speed] (FdSP): Slower, only operates if [Ref.2 channel] (Fr2) is set to [HMI] (LCC) and if a different key has been

assigned to [+ speed]. Press the key to run the drive and decrease the speed. Press STOP to stop the drive.

[T/K] (Ft): Command via the display terminal: Takes priority over [Cmd switching] (CCS) and over

[Ref. 2 switching] (rFC ).

Fn2 [F2 key assignment]

[No] (nO)

Identical to [F1 key assignment] (Fn 1) page 142.

Fn3 [F3 key assignment]

[No] (nO)

Identical to [F1 key assignment] (Fn 1) page 142.

Fn4 [F4 key assignment]

[No] (nO)

Identical to [F1 key assignment] (Fn 1) page 142.

bMp [HMI cmd.]

[Stop] (StOP)

When the [T/K] (Ft) function is assigned to a key and that function is active, this parameter defines the behavior at the moment

when control returns to the graphic display terminal or remote display terminal.

StOp

bUMF

[Stop] (StOP): Stops the drive (although the controlled direction of operation and reference of the previous channel are copied

(to be taken into account on the next RUN command)).

[Bumpless] (bUMF): Does not stop the drive (the controlled direction of operation and the reference of the previous channel

are copied)

These parameters only appear if the corresponding function has been selected in another menu. When the parameters can

also be accessed and adjusted from within the configuration menu for the corresponding function, their description is detailed

in these menus, on the pages indicated, to aid programming.

DRI- > CONF > FULL > CTL-

Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

1 2 ... 137 138 139 140 141 142 143 144 145 146 147 ... 318 319

Commentaires sur ces manuels

Pas de commentaire

Schneider Electric Altivar 32 Manuel d'installation Page 142

Commentaires sur ces manuels

Produits connexes et manuels pour Tournevis électriques Schneider Electric Altivar 32