Schneider Electric Altivar 32 Manuel d'installation Page 23
- Page / 141
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Configuration and Parameters
S1A28701 03/2010 23
Network Settings
The parameters are accessible via [CONFIGURATION] (COnF-), [FULL] (FULL-),
[COMMUNICATION] (COM-) menu and [COMMUNICATION CARD] (Cbd-) submenu.
NOTE: Before entry begins, the IP address displayed is the active IP address.
Assigning IP Addresses
The drive needs 3 IP addresses:
• The drive IP address.
• The subnet mask.
• The gateway IP address.
These IP addresses can be entered directly: Using the integrated display terminal. Using the graphic display
terminal. Or using the SoMove software. They can be provided by:
• A BOOTP server (correspondence between the MAC address and the IP addresses).
• Or a DHCP server (correspondence between Device Name [DEVICE NAME] and the IP addresses).
If an IP address other than 0.0.0.0 has been entered using the display terminal or the SoMove software,
assignment using a server is disabled.
Parameter Description
(HMI mnemonic)
Range or Listed Values Default Long Name Short
Name
Access Parameter
Number
[Ethernet protocol] (EthM)
This parameter defines which protocol is
used for implicit exchanges
0:Modbus TCP
1:EtherNet/IP
0 [Modbus TCP] (MtCP)
(EIP)
R/W 64241
[Rate setting] (rdS)
Rate and data settings
0: Autodetect
1: 10 Mbps Full
2: 10 Mbps Half
3: 100 Mbps Full
4: 100 Mbps Half
Auto [Auto]
[10M. full]
[10M. half]
[100M. full]
[100M. half]
(AUtO)
(10F)
(10H)
(100F)
(100H)
R/W 64251
[IP mode] (IpM)
Use this parameter to select the IP
address assignment method
0: Man
1: BOOTP
2: DHCP
DHCP [fixed]
[BOOTP]
[DHCP]
(MAnU)
(bOOt)
(dHCP)
R/W 64250
[IP card] (IPC)
(IPC1) (IPC2) (IPC3) (IPC4)
These fields are editable when IP mode
is set to Fixed address
0 to 255 for each 4 fields -
[139.160.069.241] (139)
(160)
(069)
(241)
R/W 64212
64213
64214
64215
[IP Mask] (IPM)
(IPM1) (IPM2) (IPM3) (IPM4)
These fields are editable when IP mode
is set to Fixed address
0 to 255 for each 4 fields - [255.255.254.0] (255)
(255)
(254)
(0)
R/W 64216
64217
64218
64219
[IP Gate] (IPG)
(IPG1) (IPG2) (IPG3) (IPG4)
These fields are editable when IP mode
is set to Fixed address
0 to 255 for each 4 fields - [0.0.0.0] (0)
(0)
(0)
(0)
R/W 64220
64221
64222
64223
[MAC @] (MAC)
MAC address display
[00-80-F4-XX-XX-XX] - [00-80-F4-XX-XX-XX] 0080
F4---
XX
XXXX
R 64267
64268
64269
- Altivar 32 1
- 2 S1A28701 03/2010 2
- Table of Contents 3
- About the Book 7
- Presentation 9
- Overview 10
- Transparent Ready 10
- • Perform remote diagnostics 10
- Modbus TCP 11
- Notation 13
- Hardware Setup 14
- Hardware Presentation 15
- Installation 15
- Installation Topology 19
- LED’s Indicators 20
- LED 3: Network Status 21
- LED Behavior Detail 21
- Configuration and Parameters 22
- S1A28701 03/2010 23 23
- Modbus TCP Settings 25
- FDR Settings 28
- EtherNet/IP Settings 29
- • ICMP client: not supported 36
- Transport Layer Protocols 37
- Modbus TCP Frames 40
- S1A28701 03/2010 41 41
- (LFF) parameter 43
- Unit ID: 255 46
- Unit ID: 0 46
- S1A28701 03/2010 47 47
- S1A28701 03/2010 49 49
- Modbus Messaging 52
- EtherNet/IP Features 53
- • CIP basic speed control 54
- • CIP extended speed control 54
- S1A28701 03/2010 55 55
- S1A28701 03/2010 57 57
- S1A28701 03/2010 59 59
- Detected Fault Management 60
- ATV32 Configuration in ETC100 61
- Procedure 62
- • Choose the Network name (1) 62
- • Configure ETC100 (2) 63
- • Double-click on ATV32 (1) 64
- • Choose a name (2) 64
- • Select “link parameter” (4) 64
- • Select all the items (2) 65
- • Define the items (3) 65
- Unity Update 66
- Profiles 69
- What's in this Chapter? 72
- Functional Description 73
- CiA402 State Chart 74
- Description of States 75
- Stop Commands 78
- Assigning Control Word Bits 78
- Status Word (EtA) 79
- Starting Sequence 80
- Bus or network 81
- CIP Objects Overview 88
- Object 28hex (Motor Data) 89
- Transparent Ready Features 92
- Startup Detailed Behavior 94
- FDR Operation Behavior 95
- Local Configuration 97
- • Card IP address 97
- • Subnet mask 97
- • Gateway IP address 97
- S1A28701 03/2010 99 99
- Embedded Webserver 100
- Connexion to the Webserver 101
- Pages Description 102
- • 0: No communication check 107
- Modbus Messaging Statistics 109
- TCP/IP Statistics 109
- EtherNet/IP Statistics 110
- S1A28701 03/2010 111 111
- Installing the EDS File 113
- Click “Next” button 114
- S1A28701 03/2010 115 115
- S1A28701 03/2010 117 117
- S1A28701 03/2010 119 119
- Explicit Messaging 120
- S1A28701 03/2010 121 121
- CIP Objects 123
- Supported Object Classes 124
- • CIP device on Ethernet/IP 124
- • AC/DC drive 124
- • VSD specific 124
- Identity Object (F1h) 124
- S1A28701 03/2010 125 125
- Message Router Object (F2h) 127
- Supported Instance Attributes 128
- Supported Class Services 129
- Supported Instance Services 129
- TCP/IP Interface Behavior 129
- (Status = 16#00000000) 129
- Ethernet Link Object (F6h) 130
- Assembly Object (04 hex) 131
- S1A28701 03/2010 132
- Motor Data Object (28h) 135
- Supported Class Attributes 136
- AC/DC Drive Object (2Ah) 137
- Supported Instance 138
© 2020, manymanuals.fr. Tous droits réservés | 1.401 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels