Schneider Electric Xantrex XW Guide d'installation Page 123
- Page / 166
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
The Xantrex XW Automatic Generator Start
975-0239-01-01 5–9
This manual for use by qualified personnel only
Preparing an Installation
Before installing the Xantrex XW Automatic Generator Start Module, consider
how and where the unit will be mounted. Pre-plan the connection routes between
the Xantrex XW Automatic Generator Start, the generator, thermostats, and the
Xantrex XW Automatic Generator Start. Refer to the Xantrex XW AGS Owner’s
Guide for additional information.
See Chapter 3, “Xantrex Xanbus Network Installation”, for more information about
installing a Xantrex Xanbus-enabled device as part of a network-managed
power system.
Materials and Tools Required
The following tools and materials may be needed to install the Xantrex XW
Automatic Generator Start:
❐ Mounting template (supplied)
❐ Wiring harness (manufacturer part number 809-0917, supplied)
❐ Four #6 screws, 1¼ inch (supplied)
❐ #16 or #18 AWG wire (see “Wire Size and Length” on page 5–13)
❐ Schneider Electric network cables or equivalent (Category 5)
❐ Network terminators (if required)
❐ Phillips screwdriver
❐ Wire cutters and wire strippers
Choosing a Location
The Xantrex XW Automatic Generator Start should be installed in a location that
meets the following requirements:
Dry
The unit is intended for use in a dry location. The Xantrex XW
Automatic Generator Start
complies with UL458 Marine
Supplement drip-test requirements, but the location should be as
dry as possible.
Cool
The Xantrex XW Automatic Generator Start
operates between
-4 and 122 °F (-20 and 50 °C).
Safe
The Xantrex XW Automatic Generator Start
is not ignition
protected. Do not install it in areas requiring ignition-protected
equipment, such as compartments housing gasoline engines.
Close to
generator
Avoid excessive wire lengths and use the recommended wire
lengths and sizes (see “Wire Size and Length” on page 5–13).
It is more important for the Xantrex XW Automatic Generator Start
to be close to the generator than close to the inverter, although
for safety reasons, the Xantrex XW Automatic Generator Start
should not be installed in the same compartment as a
gasoline-powered generator.
- Xantrex™ XW Power System 1
- Xantrex XW Power System 3
- Copyright and Contact 4
- About This Guide 5
- Conventions Used 6
- Related Information 6
- Important Safety Instructions 7
- Limitations on Use 8
- Single-phase Operation Only 8
- Explosive Gas Precautions 8
- FCC Information to the User 9
- Contents 11
- A Specifications 14
- B Wiring Diagrams 14
- 1 Introduction 21
- System Overview 22
- Xantrex XW Conduit Box 24
- 975-0239-01-01 1–5 25
- FGA Number: 28
- 865-1050 28
- 865-1060 29
- 2 Inverter/Charger 31
- Pre-Installation 32
- Clearance Requirements 34
- Mounting 34
- Inverter/Charger Installation 36
- 2–6 975-0239-01-01 36
- Step 2: Mounting the Inverter 37
- Step 4: Wiring the Inverter 39
- Inverter Grounding 44
- Grounding the DC System 45
- 975-0239-01-01 2–17 47
- Making DC Connections 48
- Making AC Connections 50
- CAUTION: 51
- Damage to the Inverter 51
- Grounding the AC System 53
- 2–26 975-0239-01-01 56
- 975-0239-01-01 2–27 57
- Distribution Panel 58
- AUX Port 60
- User Line Wiring 61
- AUX Port Terminal Assignments 61
- Confirm All Connections 62
- Enable the Inverter 63
- AC Voltage Check 64
- 2–36 975-0239-01-01 66
- Installation Steps 67
- Power Distribution Panel 68
- 975-0239-01-01 2–39 69
- 975-0239-01-01 2–41 71
- 2–42 975-0239-01-01 72
- See Figure 2-9 on page 2–14 76
- 975-0239-01-01 2–47 77
- 2–48 975-0239-01-01 78
- 2–52 975-0239-01-01 82
- 975-0239-01-01 2–53 83
- 3 Xantrex Xanbus 85
- The Xantrex Xanbus System 86
- Network Components 87
- Ordering Network Components 88
- Network Layout 89
- Installing the Network 90
- 4 Xantrex XW Solar 93
- PV Array Requirements 94
- Remove screws to access 97
- Removing Knockouts 98
- Mounting the Controller 99
- Secure with two more screws 100
- Place keyhole slot 100
- ¼" 6 mm 100
- Grounding 101
- WARNING: Shock Hazard 102
- WARNING: Fire Hazard 102
- Ungrounded Arrays 103
- Minimum Wire Gauge 105
- Over-current Protection 105
- Current Rating 105
- WARNING: Equipment damage 106
- Commissioning 111
- 5 Xantrex XW System 115
- Materials and Tools Required 117
- Choosing a Location 117
- WARNING: Explosion hazard 117
- WARNING: Shock hazard 118
- Rotate tabs to 119
- CAUTION: Equipment damage 120
- Verifying the Installation 122
- Preparing an Installation 123
- WARNING: Explosion Hazard 124
- CAUTION: Shock Hazard 126
- N/OFF/LED Indicator 128
- N/OFF/LED Indicator return 128
- Connecting the Generator 129
- CAUTION: Equipment Damage 131
- N/OFF switch. This light 132
- Verifying Power Is Available 135
- A Specifications 137
- Electrical Specifications 138
- Connection 139
- Specifications 140
- A–4 975-0239-01-01 140
- Ambient Temperature (°C) 141
- Xantrex XW Series Efficiency 142
- Charging Power Factor 143
- Mechanical Specifications 144
- Accessories 145
- B Wiring Diagrams 147
- 975-0239-01-01 B–3 149
- Xantrex Xanbus 150
- Network Terminator 150
- Xantrex XW Inverter/Charger 150
- Wiring Diagrams 152
- B–6 975-0239-01-01 152
- 975-0239-01-01 B–7 153
- B–8 975-0239-01-01 154
- C Alternate System 155
- 975-0239-01-01 C–3 157
- C–4 975-0239-01-01 158
- 975-0239-01-01 C–5 159
- CAUTION: Damage to Equipment 161
- Schneider Electric 166
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Schneider Electric Xantrex XW
(58 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels