Schneider Electric Altivar 58 VW3-A58101 Manuel d'utilisateur Page 17
- Page / 112
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
VVDED397047US R8/01 ALTIVAR
58 Keypad Display
08/01 Chapter 1 — Overview
© 1998–2001 Schneider Electric All Rights Reserved
17
ACCESS LEVELS
Figure 5: Rear View of Keypad Display
The position of the access locking switch on the back of the programming
keypad display allows three levels of access to the menus. Access to the
menus can also be prevented by using an access code (see the 7—File
menu on page 79).
Locked Position – Display Mode: use when the motor is running
to prevent modifications to the drive controller programming.
• You can select the dialog language in the LANGUAGE menu.
• You can display the macro-configuration or the pre-programmed
values for the selected application in the MACRO-CONFIG menu.
• You can display the voltage and power rating of your drive controller in
the IDENTIFICATION menu.
• You can display the electrical values, the operational status, or fault in
the 1—DISPLAY menu.
Partial Lock Position – Display and Adjustment Modes: this
level is used during startup for access to basic setup parameters.
• You can do everything listed above.
• You can use the 2—ADJUST menu to adjust parameters which are
accessible when the motor is running.
Connector (9-pin SUB-D male):
- for direct connection to the drive controller
- for remote mounting, the keypad display can be
connected using a cable provided in kit
VW3A58103
Switch for access locking:
- locked : display mode only, adjustment and
position configuration parameters not
accessible
- partial : display mode and adjustment
lock parameters accessible
position
- total : display mode, adjustment and
unlock configuration parameters accessible
position
- 58 Adjustable Speed 1
- Drive Controllers 1
- Instruction Bulletin 1
- 08/01 Contents 3
- Contents 08/01 4
- CHAPTER 1—OVERVIEW 7
- (Continued) 10
- Chapter 1 — Overview 08/01 12
- 50 Hz 60 Hz 13
- 50/60 Hz switch 13
- VVDED397047US R8/01 ALTIVAR 15
- 08/01 Chapter 1 — Overview 15
- Figure 6: Menus 19
- CHAPTER 2—MENUS 21
- Validate? ENT/ESC 23
- CUS:Customize 24
- 08/01 Chapter 2 — Menus 25
- Handling Macro-Configuration 32
- Macro-Configuration 34
- Torque Macro-Configuration 35
- Reassignment (Continued) 37
- Chapter 2 — Menus 08/01 38
- T1 = 1/Acc 42
- T1 = 1/Dec 42
- drive controller to control 44
- 24 V LI1 LI2 LIx 45
- ATV58 Terminal strip 45
- LI1: Stop 45
- LI2: Forward 45
- LIx: Reverse 45
- ATV58 terminal strip 46
- 24 V LI1 LIx 46
- LI1: Forward 46
- AOL AOH 20 48
- Parameter 48
- LI1 LI2 LI3 LI4 +24 AIX 58
- Input Code Range Description 67
- T = non-adjustable delay 70
- Table 21: 6—Fault Menu 77
- Parameter Code Description 78
- Adjustment 78
- Factory 78
- Wiring OK? ENT/ESC 80
- Password Fault 82
- Red FAULT LED 85
- L1 L2 L3 PA PB U V W 89
- L1 L2 + – UVW 89
- FAULT CODES AND MESSAGES 91
- ItH, see 93
- ≥ 200 ms) 94
- Trip Point Reset Point 95
- Table 33: Menu 7—File Menu 100
- Menu 3 – DRIVE Menu (page 39) 101
- Menu 5– I/O Menu (page 51) 102
- Menu 6 – FAULT Menu (page 75) 102
- Menu 7 – FILES Menu (page 79) 102
- Continued on 103
- Catalog No. Description 104
- Description For Use on Drives 105
- Catalog 105
- 58 Keypad Display 107
- 08/01 Index 107
- Index 08/01 108
- Square D Company 112
- 8001 Hwy 64 East 112
- Knightdale, NC 27545 USA 112
Produits connexes et manuels pour Mesure, test et contrôle Schneider Electric Altivar 58 VW3-A58101
(40 pages)AudioBahn ACS2035N manuels
Manuels d'utilisation et guides de l'utilisateur pour Haut-parleurs pour voitures AudioBahn ACS2035N.
Nous fournissons des manuels en pdf 1 AudioBahn ACS2035N à télécharger gratuitement par type de document : Instructions d'exploitation
Commentaires sur ces manuels