Schneider Electric Multi-Loader Spécifications télécharger pdf (Page 27)

Combinations for

customer assembly

(continued)

Altivar

variable speed drives

Motor starters: Three-phase supply voltage

200 to 240 V

Motor starters (continued)

Standard

power

ratings of

three-phase

4-pole

50/60 Hz Hz

motors

(2)

Variable speed

drive

Combination with control circuit

(circuit-breaker + contactor)

Minimum conguration

(circuit-breaker only)

TeSys

contactor

(1)

TeSys

motor

circuit-breaker

(3)

Operating

range or

rating

Maximum

short-circuit

current Icu

Modular

circuit-breaker

(4)

kW HP A kA

M1 A1 Q1 KM1

Three-phase supply voltage: 200 to 240 V 50/60 Hz

0.18 0.25 ATV12H018M3 GV2ME07 1.6 to 2.5 > 100 LC1K09

GV2L07 2.5 > 100

4-pole C60N 6 10

0.37 0.55 ATV12p037M3 GV2ME08 2.5 to 4 > 100 LC1K09

GV2L08 4 > 100

4-pole C60N 6 10

0.75 1 ATV12p075M3 GV2ME14 6 to 10 > 100 LC1K09

GV2L14 10 > 100

4-pole C60N 10 10

1.5 2 ATV12pU15M3 GV2ME16 9 to 14 > 100 LC1K12

GV2L16 14 > 100

4-pole C60N 16 10

2.2 3 ATV12pU22M3 GV2ME20 13 to 18 > 100 LC1D18

GV2L20 18 > 100

4-pole C60N 20 10

3 – ATV12pU30M3 GV2ME21 17 to 23 50 LC1D25

GV2L22 25 50

4-pole C60N 20 10

4 5 ATV12pU40M3 GV2ME32 24 to 32 50 LC1D25

GV2L22 25 50

4-pole C60N 32 10

Combinations of C60N circuit-breakers/Vigi C60 add-on modules

C60N

2-pole/4-pole

Vigi C60

Rating (A) Rating (A) Type (5) Sensitivity

6 25 A “si” 30 mA

10 25 A “si” 30 mA

16 25 A “si” 30 mA

20 25 A “si” 30 mA

32 40 A “si” 30 mA

Recommendations for special uses:

All RH10/RH21/RH99/RHU residual current protection devices with separate sensors are

compatible as long as the type and sensitivity of the add-on modules given in the table above are

observed.

It is advisable to connect one RCD (residual current device) per drive. In this case, a type B RCD

must not be located downstream of a type A or AC RCD.

(1) For a complete list of references for TeSys contactors, please refer to the "Motor starter

solutions - Control and protection components" and "Motor starters up to 150 A" catalogs or visit

"www.schneider-electric.us".

(2) Motor power indicated for combination with an ATV12Hppppp drive with the same rating.

For combination with an ATV12Pppppp drive, refer to the specic manual for the Altivar

base plate version, available on our website at “www.schneider-electric.us”.

(3) TeSys motor circuit-breakers:

- GV2MEpp: Thermal magnetic motor circuit-breakers with pushbutton control

- GV2Lpp: Magnetic motor circuit-breakers with control by rotary knob

(4) 4-pole C60N modular circuit-breaker

(5) For additional protection against direct contact, with a three-phase power supply and access

to the DC bus terminals (PA/+ and PC /-), the add-on module must be type B with a sensitivity of

30 mA.

Introduction:

page 8

Specications:

page 10

References:

page 14

Dimensions:

page 18

Connections:

page 22

W/T3

U/T1

V/T2

R/L1

S/L2

T/L3

Motor starter with three-phase power supply

Q1:

C60N4P

KM1:

TeSys LC1pppp

(if control circuit)

A1:

ATV12ppppM3

Q1:

GV2pppp

M1:

200..240 V three-phase

asynchronous motor

Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 39 40

Commentaires sur ces manuels

Pas de commentaire

Schneider Electric Multi-Loader Spécifications Page 27

Commentaires sur ces manuels

Produits connexes et manuels pour Mesure, test et contrôle Schneider Electric Multi-Loader